The QJ deep-well pump, also known as a QJ well-submersible pump, is a vertical multistage centrifugal pumping unit in which the submersible motor is directly coupled to the pump and the complete unit operates underwater. It typically comprises a submersible motor, pump body, discharge column pipe, power cable and control cabinet.
The motor is installed below the pump. Water enters the impeller stages and is pressurized in stages before being conveyed to the surface through the discharge column pipe.
Designed for deep-well water lifting, the QJ series is manufactured to GB/T 2816, Submersible Pumps for Wells. The stated series-wide flow range is 5–650 m³/h, with total head exceeding 600 m for some configurations. Applications include deep-well water supply, mine drainage and municipal water systems.
Model designation example: 200QJ 50-65/5
- 200: Nominal well diameter designation; confirm the required minimum well diameter against the specific pump's dimensions.
- Submersible pump for wells.
- 50: Rated flow, in m³/h.
- 65: Rated head, in metres.
- 5: Number of impeller stages.
1. Pump and motor operate underwater
The pump and submersible motor are directly coupled and operate as a submerged unit. A conventional pump room is not required, which can reduce installation space and civil-work costs. Installation generally involves lowering the unit into the well or sump and connecting the discharge pipe and cable.
2. Multistage design for high head
The vertical multistage arrangement raises pressure stage by stage. The source states that total head can exceed 600 m in some configurations, supporting deep-well applications.
3. No priming required
Because the pump operates submerged, it does not require priming or vacuum priming before startup.
4. Water-lubricated bearings
The pump's guide bearings are water-lubricated and cooled by the pumped water. No grease or oil is required for these bearings, avoiding lubricant contamination of the water.
5. Submersible motor
The motor is available in water-filled or oil-filled designs. Its stator windings use waterproof insulation or sealing. A temperature-protection device can be fitted to help prevent overheating.
6. Efficient operation
The pump uses a hydraulic design with cast impellers and diffusers. Smooth flow passages are intended to support good hydraulic efficiency and compliance with applicable energy-efficiency criteria.
7. Low noise at ground level
Since the pump and motor operate underwater, there are no exposed moving parts at ground level, and noise and vibration transmitted to the surface are reduced.
8. Material options
Wetted parts can be selected from cast iron, ductile iron, 304 stainless steel or 316L stainless steel, according to water quality and corrosion requirements.
The QJ series is used for deep-well water extraction and groundwater development, including:
- Deep-well water supply for irrigation, sprinklers, drip systems and landscaping.
- Water extraction from municipal supply wells and other water-system duties.
- Mine-water discharge, groundwater control and mining water supply.
- Cooling-water systems, boiler feed and general industrial water service.
- Groundwater removal from construction excavations and tunnel works.
- Drinking-water supply for people and livestock.
- Ground-source heat-pump systems: Groundwater extraction and reinjection, subject to system design requirements.
- Extraction of geothermal hot water, subject to the pump's material and temperature limits.
- Fire-water supply: Water extraction from dedicated fire-water wells, subject to applicable system approvals.
1. Design Standards
Design, manufacture and inspection are stated to comply with GB/T 2816, Submersible Pumps for Wells, and GB/T 2818, Submersible Asynchronous Motors for Wells. Hydraulic performance testing is conducted with reference to applicable standards.
2. Construction and Operating Principle
The QJ pump consists of a submersible motor, a multistage pump assembly, discharge column pipe, power cable and control cabinet. The motor is positioned below the pump and connected directly through a coupling.
Water enters through the intake at the lower part of the pump. The first impeller raises its pressure, after which a diffuser guides it to the next impeller. This process repeats through the stages, and the pressurized water is delivered to the surface through the discharge pipe.
3. Pump Construction
The pump is a vertical, multistage, sectional design. Each stage comprises an impeller, diffuser and casing section, which are secured together by tie rods. The pump shaft is supported by upper and lower guide bearings; the guide bearings are water-lubricated.
4. Motor Construction
The submersible motor is a water-filled or oil-filled three-phase asynchronous motor. Its stator windings use water-resistant magnet wire or sealed waterproof insulation. The motor housing is made of stainless steel or cast iron. A mechanical seal or oil seal is fitted at the shaft extension to help prevent sand from entering the motor.
5. Wetted-Part Material Options
|
|
|
|
|
HT200 cast iron, QT500 ductile iron, 304 / 316L stainless steel |
||
|
HT200 cast iron, 304 / 316L stainless steel |
Clean water and low-sand water |
|
|
2Cr13, 304 or 316L stainless steel |
||
|
Steel or stainless-steel pipe |
6. Submersible-Motor Specifications
|
|
|
|
Water-filled or oil-filled three-phase asynchronous motor |
|
|
380 V / 660 V / 6 kV / 10 kV, depending on power rating |
|
|
50 Hz |
|
|
IP68 |
|
|
Water-cooled; water flow around the motor housing carries away heat |
|
7. Installation and Operating Conditions
- Three-phase AC, 50 Hz; the source specifies 380 V or 660 V with voltage variation of ±5%.
- Up to 20℃ standard; up to 40℃ under special conditions with sufficient cooling-water flow.
- No more than 0.01% by weight.
- No more than 400 mg/L.
- The well should be straight, and its diameter must meet the minimum requirement for the selected pump.
- Up to 300 m, as stated for the series.
8. Stated Operating Range
|
|
|
|
5–650 m³/h across the series |
|
|
3–30 m, depending on flow |
|
|
Above 600 m for some configurations |
|
|
2,850 / 2,900 r/min, 2-pole motor |
|
|
100–400 mm, depending on model |
|
|
<=300 m |
|
|
<=20℃ standard; <=40℃ for special configurations |
|
|
<=0.01% by weight |
|
|
380 V / 660 V / 6 kV / 10 kV, 50 Hz, according to motor rating |

|
|
|
|
|
|
|
|
|
Pump-body outside diameter (mm) |
|
150QJ5 |
5 |
6-20 |
2-25 |
12-500 |
0.55-11 |
150 |
DN25/DN32 |
133 |
|
150QJ10 |
10 |
6-18 |
2-25 |
12-450 |
0.75-18.5 |
150 |
DN32/DN40 |
133 |
|
150QJ20 |
20 |
6-16 |
2-22 |
12-352 |
1.5-30 |
150 |
DN40/DN50 |
133 |
|
150QJ32 |
32 |
6-12 |
2-20 |
12-240 |
2.2-37 |
150 |
DN50 |
133 |
|
175QJ10 |
10 |
8-24 |
2-20 |
16-480 |
1.1-22 |
175 |
DN32/DN40 |
159 |
|
175QJ20 |
20 |
8-22 |
2-18 |
16-396 |
2.2-37 |
175 |
DN40/DN50 |
159 |
|
175QJ32 |
32 |
8-18 |
2-16 |
16-288 |
3.0-45 |
175 |
DN50 |
159 |
|
175QJ40 |
40 |
6-16 |
2-15 |
12-240 |
3.0-55 |
175 |
DN65 |
159 |
|
175QJ50 |
50 |
6-14 |
2-14 |
12-196 |
4.0-55 |
175 |
DN65 |
159 |
|
200QJ10 |
10 |
10-30 |
2-20 |
20-600 |
1.5-30 |
200 |
DN32/DN40 |
184 |
|
200QJ20 |
20 |
10-28 |
2-18 |
20-504 |
3.0-45 |
200 |
DN40/DN50 |
184 |
|
200QJ32 |
32 |
10-26 |
2-16 |
20-416 |
4.0-55 |
200 |
DN50 |
184 |
|
200QJ40 |
40 |
8-24 |
2-15 |
16-360 |
5.5-75 |
200 |
DN65 |
184 |
|
200QJ50 |
50 |
8-20 |
2-14 |
16-280 |
5.5-75 |
200 |
DN65 |
184 |
|
200QJ63 |
63 |
8-18 |
2-12 |
16-216 |
7.5-75 |
200 |
DN80 |
184 |
|
200QJ80 |
80 |
6-14 |
2-10 |
12-140 |
7.5-75 |
200 |
DN80 |
184 |
|
200QJ100 |
100 |
6-12 |
2-8 |
12-96 |
11-75 |
200 |
DN100 |
184 |
|
250QJ20 |
20 |
12-38 |
2-18 |
24-684 |
4.0-75 |
250 |
DN40/DN50 |
233 |
|
250QJ32 |
32 |
12-36 |
2-16 |
24-576 |
5.5-90 |
250 |
DN50 |
233 |
|
250QJ40 |
40 |
10-34 |
2-15 |
20-510 |
7.5-110 |
250 |
DN65 |
233 |
|
250QJ50 |
50 |
10-30 |
2-14 |
20-420 |
7.5-110 |
250 |
DN65 |
233 |
|
250QJ63 |
63 |
10-28 |
2-12 |
20-336 |
11-110 |
250 |
DN80 |
233 |
|
250QJ80 |
80 |
8-24 |
2-10 |
16-240 |
11-110 |
250 |
DN80 |
233 |
|
250QJ100 |
100 |
8-20 |
2-8 |
16-160 |
15-110 |
250 |
DN100 |
233 |
|
250QJ125 |
125 |
6-16 |
2-7 |
12-112 |
18.5-110 |
250 |
DN100 |
233 |
|
250QJ140 |
140 |
6-14 |
2-6 |
12-84 |
18.5-110 |
250 |
DN125 |
233 |
|
250QJ160 |
160 |
6-12 |
2-5 |
12-60 |
22-110 |
250 |
DN125 |
233 |
|
250QJ200 |
200 |
4-8 |
2-4 |
8-32 |
22-75 |
250 |
DN150 |
233 |
|
300QJ20 |
20 |
15-50 |
2-16 |
30-800 |
5.5-90 |
300 |
DN40/DN50 |
281 |
|
300QJ32 |
32 |
15-48 |
2-15 |
30-720 |
7.5-110 |
300 |
DN50 |
281 |
|
300QJ40 |
40 |
12-45 |
2-14 |
24-630 |
11-132 |
300 |
DN65 |
281 |
|
300QJ50 |
50 |
12-42 |
2-13 |
24-546 |
11-160 |
300 |
DN65 |
281 |
|
300QJ63 |
63 |
12-40 |
2-12 |
24-480 |
15-160 |
300 |
DN80 |
281 |
|
300QJ80 |
80 |
10-36 |
2-11 |
20-396 |
18.5-185 |
300 |
DN80 |
281 |
|
300QJ100 |
100 |
10-32 |
2-10 |
20-320 |
22-200 |
300 |
DN100 |
281 |
|
300QJ125 |
125 |
8-28 |
2-9 |
16-252 |
22-220 |
300 |
DN100 |
281 |
|
300QJ140 |
140 |
8-24 |
2-8 |
16-192 |
22-220 |
300 |
DN125 |
281 |
|
300QJ160 |
160 |
8-22 |
2-7 |
16-154 |
30-220 |
300 |
DN125 |
281 |
|
300QJ200 |
200 |
6-18 |
2-6 |
12-108 |
30-220 |
300 |
DN150 |
281 |
|
300QJ240 |
240 |
6-14 |
2-5 |
12-70 |
37-185 |
300 |
DN150 |
281 |
|
300QJ320 |
320 |
4-10 |
2-4 |
8-40 |
37-185 |
300 |
DN200 |
281 |
|
350QJ40 |
40 |
15-55 |
2-14 |
30-770 |
11-160 |
350 |
DN65 |
330 |
|
350QJ50 |
50 |
15-52 |
2-13 |
30-676 |
15-185 |
350 |
DN65 |
330 |
|
350QJ63 |
63 |
15-50 |
2-12 |
30-600 |
18.5-220 |
350 |
DN80 |
330 |
|
350QJ80 |
80 |
12-48 |
2-11 |
24-528 |
22-250 |
350 |
DN80 |
330 |
|
350QJ100 |
100 |
12-45 |
2-10 |
24-450 |
30-280 |
350 |
DN100 |
330 |
|
350QJ125 |
125 |
10-40 |
2-9 |
20-360 |
30-300 |
350 |
DN100 |
330 |
|
350QJ140 |
140 |
10-36 |
2-8 |
20-288 |
37-300 |
350 |
DN125 |
330 |
|
350QJ160 |
160 |
10-34 |
2-7 |
20-238 |
45-300 |
350 |
DN125 |
330 |
|
350QJ200 |
200 |
8-30 |
2-6 |
16-180 |
45-300 |
350 |
DN150 |
330 |
|
350QJ240 |
240 |
8-26 |
2-5 |
16-130 |
55-280 |
350 |
DN150 |
330 |
|
350QJ320 |
320 |
6-20 |
2-4 |
12-80 |
55-250 |
350 |
DN200 |
330 |
|
350QJ400 |
400 |
6-16 |
2-3 |
12-48 |
55-220 |
350 |
DN200 |
330 |
|
400QJ50 |
50 |
18-65 |
2-15 |
36-975 |
15-220 |
400 |
DN65 |
375 |
|
400QJ63 |
63 |
18-62 |
2-14 |
36-868 |
18.5-250 |
400 |
DN80 |
375 |
|
400QJ80 |
80 |
15-60 |
2-13 |
30-780 |
22-280 |
400 |
DN80 |
375 |
|
400QJ100 |
100 |
15-55 |
2-12 |
30-660 |
30-315 |
400 |
DN100 |
375 |
|
400QJ125 |
125 |
12-50 |
2-11 |
24-550 |
37-355 |
400 |
DN100 |
375 |
|
400QJ140 |
140 |
12-46 |
2-10 |
24-460 |
45-400 |
400 |
DN125 |
375 |
|
400QJ160 |
160 |
12-42 |
2-9 |
24-378 |
55-400 |
400 |
DN125 |
375 |
|
400QJ200 |
200 |
10-38 |
2-8 |
20-304 |
55-450 |
400 |
DN150 |
375 |
|
400QJ240 |
240 |
10-34 |
2-7 |
20-238 |
75-450 |
400 |
DN150 |
375 |
|
400QJ320 |
320 |
8-28 |
2-6 |
16-168 |
75-500 |
400 |
DN200 |
375 |
|
400QJ400 |
400 |
8-24 |
2-5 |
16-120 |
90-500 |
400 |
DN200 |
375 |
|
400QJ500 |
500 |
6-18 |
2-4 |
12-72 |
90-450 |
400 |
DN250 |
375 |
If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.
लोकप्रिय टैग: qj deep-well submersible pump, China qj deep-well submersible pump manufacturers, factory


